TDS Mini Controller (0.0 to 199.9 ppm)

SKU : f24a5aa620cf

The BL983315 is a compact, panel mounted, process controller for measuring total dissolved solids (TDS) of a process stream that is within the 0.0 to 199.9 ppm (mg/L) range. The device features a large LCD with protective cover. Users may choose from automatic or manual dosing modes. When in automatic mode the dry contact relay is activated when a reading is above the set point. The relay can be used to supply power to a dosing pump or a solenoid connected to a valve. The BL983315 can also be used to monitor the quality of water produced from ion exchange, reverse osmosis (RO) or distillation.  *The BL983315 uses a 0.5 conversion factor in which 1.0 ?S/cm = 0.5 ppm.

  • Multicolor LED Indicator
  • Fire Retardant Casing
  • Fire Retardant Casing
Pemesanan dapat melalui :
SKU f24a5aa620cf Kategori :
Share this :

Deskripsi

tds-mini-controller-bl983315-angle

Adjustable Dry Contact Dosing Relay

The BL983315 features a dosing relay that is activated when the reading is above a user programmable set point.

Programmable Overdose Protection

For enhanced safety the mini controller can be programmed to deactivate the dosing relay if the set point is not reached within a specified time interval. The overdosing timer is programmable from 5 to 30 minutes or disabled.

Relay Control Override

With the flick of a switch the mini controller’s relay can be disabled (Off), placed in control (Auto), or be activated for manual operation (On) which is useful for priming a dosing pump.

Multicolor LED Indicator

Multicolor LED indicator allows an operator to quickly check the status of the controller.

  • Green = Meter in measurement mode and reading is below the set point.
  • Orange/Yellow = Reading is above the set point and the relay is activated.
  • Blinking Red = Indicates an alarm condition such as when the maximum dosing time has been exceeded.

tds-mini-controller-bl983315-rear

Fuse Protected Dosing Contacts

The relay dosing contact is rated for up to a 2A load and is fuse protected.

Labeled Termination Connections

Quick-connect terminal blocks are clearly labeled for easy connection to power, conductivity probe and relay that can be used to operate a dosing pump, valve, audible alarm, or light.

male-threaded-amperometric-probe-hi7634

1/2″ NPT Male Threaded Amperometric Probe for Mounting In-line*

The BL983315 mini controller uses the HI7634-00 conductivity probe that is available with different cable lengths.

*HI7634-00 is not included and must be ordered separately

 

front-view-installation-specs-bl

side-view-installation-specs-bl

Front View

Installation cut-out dimensions are provided as well as outside panel dimensions.

Side View

Adjustable location brackets allow the controller to slide easily and securely into place.

 

 

 

Specification NameDetail
SKUBL983315
TDS Range0.0 to 199.9 mg/L (ppm)
TDS Resolution0.1 mg/L (ppm)
TDS Accuracy (@25°C/77°F)±2% F.S.
TDS Conversion Factor0.5
Temperature Compensationautomatic from 5 to 50°C (41 to 122°F) with ß =2%/ºC
Calibrationmanual, with CAL trimmer
Dosing Relaymaximum 2A (fuse protected), 250 Vac, 30 VDC Contact close when measure: < setpoint
Overtimeadjustable, typically from 5 to approximately 30 minutes
Power Supplymodels “-0”: 12 VDC adapter (included)models “-1”: 115/230 VAC; 50/60Hz
Dimensions83 x 53 x 99 mm (3.3 x 2.1 x 3.9’’)
Weightmodels “-0”: 200 g (7.1 oz.)models “-1”: 300 g (10.6 oz.)
Ordering InformationSupplied with mounting brackets, transparent cover and instruction manual.
Recommended ProbeHI7634-00 EC/TDS probe with internal temperature sensor and 2 m (6.6’) cable (not included).